![Combi ventilační žlázy Combi ventilační žlázy](https://www.dacpol.eu/7312-large_default/combi-ventilacni-zlazy.jpg)
![Combi ventilační žlázy Combi ventilační žlázy](https://www.dacpol.eu/7312-large_default/combi-ventilacni-zlazy.jpg)
Musíte být přihlášen
Category
Montaż urządzeń
Modernizacja induktorów
Urządzenia indukcyjne
asd
Fotografie slouží pouze pro informační účely. Zobrazit specifikaci produktu
please use latin characters
Air saturation with water level (humidity) depends on the temperature. In case of big temperature difference between inside and outside of the casing, the water condensation inside of the casing appears.
Example: During load change![]() |
Turn on system.
Inside temperature is usually higher then outside because of devices power losses. |
![]() |
Warm air inside the cabinet absorbs humidity, which penetrates from outside, because cabinets are not gas tight.
|
![]() |
System turned off.
Inside temperature lowers because devices are turned off. Colder air emits water, which liquefy on the inside surfaces. |
It appears especially in places, where there are big temperature jumps, in the internal installations, inside buildings.
|
![]() |
![]() In order to keep high IP level ventilation is protected by special ventilation throttles. Because of breathing membranes they provide pressure equalization. |
New ventilation gland KOMBI allows to insert cable and additionally it compensates pressure.
Kombi glands protects from accumulation of water which occur usually because of big temperature differences. ![]() |
-for inside and outside installations
|
- Material: Thermoplast
- with lightening and counter nut |
- IP: IP 66 / IP 67
- Colour: grey, RAL 7032 |
![]() |
KBM 20 |
Kombi ventilation glands
|
---|---|---|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 20 x 1,5 Tightening level: Ø 6-13 mm gland hole: Ø 20,5 mm one ventilation gland M20 must be used for 6 litres (6000 cm3) casing capacity. |
||
![]() |
KBM 25 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 25 x 1,5 Tightening level: Ø 9-17 mm gland hole: Ø 25,5 mm one ventilation gland M25 must be used for 11 litres (11000 cm3) casing capacity. |
||
![]() |
KBM 32 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 32 x 1,5 Tightening level: Ø 13-21 mm gland hole: Ø 32,5 mm one ventilation gland M32 must be used for 13 litres (13000 cm3) casing capacity. |
||
![]() |
VSB 13 |
Stopper
|
diameter: 13 mm
for ventilation glands i M20 or M25, which are not used for cable ducting Colour: Red, RAL 3000 |
||
![]() |
VSB21 |
Stopper
|
diameter: 21 mm
for ventilation glands i M25 or M32, which are not used for cable ducting Colour: Red, RAL 3000 |
-for inside and outside installations
|
- Material: Thermoplast
- with lightening and counter nut |
- IP: IP 66 / IP 67
- Colour: black, RAL 9005 |
![]() |
KBS 20 |
Kombi ventilation glands
|
---|---|---|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 20 x 1,5 Tightening level: Ø 6-13 mm gland hole: Ø 20,5 mm ventilation gland M20 must be used for 6 litres (6000 cm3) casing capacity. |
||
![]() |
KBS 25 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 25 x 1,5 Tightening level: Ø 9-17 mm gland hole: Ø 25,5 mm ventilation gland M25 must be used for 11 litres (11000 cm3) casing capacity. |
||
![]() |
KBS 32 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 32 x 1,5 Tightening level: Ø 13-21 mm gland hole: Ø 32,5 mm ventilation gland M32 must be used for 13 litres (13000 cm3) casing capacity. |
||
![]() |
VSB 13 |
Stopper
|
diameter: 13 mm
for ventilation glands M20 or M25, which are not used for cable ducting Red, RAL 3000 |
||
![]() |
VSB21 |
Stopper
|
diameter: 21 mm
for ventilation glands i M25 or M32, which are not used for cable ducting Red, RAL 3000 |
Glands for areas endangered with explosion
|
- with load and counter nut
-material - poll amid
|
- IP IP 65
- colour: black, RAL 9005 |
![]() |
AXM20 |
Thread: M20 x 1,5
For cables: Ø 5,5 - 13 mm |
assembly hole: Ø 20,5 mm
Wall thickness: 1,5 - 2 mm |
---|---|---|---|
AXM25 |
Thread: M25 x 1,5
For cables: Ø 8 - 17 mm |
assembly hole: Ø 25,5 mm
Wall thickness: 1,5 - 2 mm |
|
AXM32 |
Thread: M32 x 1,5
For cables: Ø 12 - 21 mm |
assembly hole: Ø 32,5 mm
Wall thickness: 1,5 - 3 mm |
|
AXM40 |
Thread: M40 x 1,5
For cables: Ø 17 - 28 mm |
assembly hole: Ø 40,5 mm
Wall thickness: 1,5 - 3 mm |
-for inside and outside installations
|
- Thread ISO: M 12 - M 63
- gland hole: Ø12.5 - 63.5mm |
- material: Thermoplast
- Wall thickness: up to 3 mm |
![]() |
AKM |
Twisted gland
|
---|---|---|
IP: IP 65
Tightening level: Ø 3 mm - 48 mm Colour: grey, RAL 7035 incandescent wire test IEC 60 695-2-11 750° C |
||
![]() |
ASM |
Twisted gland
|
IP: IP 66
Tightening level: Ø 3 mm - 48 mm Colour: grey, RAL 7035 incandescent wire test IEC 60 695-2-11 960° C |
||
![]() |
ASS |
Twisted gland
|
IP: IP 66 / IP 67
Tightening level: Ø 2 mm - 48 mm Colour: black, RAL 9005 incandescent wire test IEC 60 695-2-11 960° C |
-for inside and outside installations
|
- incandescent wire test
IEC 60 695-2-11 750° C |
- for holes M 16 - M 40
- gland hole Ø 16.5 - 40.5mm |
- material: Thermoplast
- Colour: grey, RAL 7035 |
![]() |
ESM |
Push in gland
|
---|---|---|
IP: IP 55
Tightening level: Ø 4.8 mm - 30 mm Wall thickness: 1.5-3.5 mm |
||
![]() |
STM |
Multi range gland
|
IP: IP 55
Tightening level: Ø 3.5 mm - 34 mm Wall thickness: 1.5-4 mm |
||
![]() |
EDK |
Push in gland
|
IP: IP 65
Tightening level: Ø 5 mm - 30 mm Wall thickness: 1.5-3.5 mm |
||
![]() |
EDR |
Push in gland for installations pipes
|
IP: IP 65
For pipes: M 16 - M 40 Wall thickness: 1.5-3.2 mm |
Operation condition
/material property |
ESM...
STM... EDK... EDR... KST... MV FP 66 |
Ste...
|
ASM... AKS...
|
ASS...
|
AKM...
|
---|---|---|---|---|---|
Ambient temperature - mean value 24h |
+35°C | +35°C | +55°C | +55°C | +55°C |
- max value | +40°C | +40°C | +70°C | +70°C | +70°C |
- min value | -25°C | -25°C | -25°C | -25°C | -25°C |
Flammability -incandescent wire test | 750°C | 650°C | 960°C | 960°C | 750°C |
IEC60595-2-1 | - | - | V-0 | V-2 | V-2 |
-UL Subject 94 | Flame resistant, self extinguishing | Flame resistant, self extinguishing | Flame resistant, self extinguishing | Flame resistant, self extinguishing | |
Toxins emission |
non halogen 1)
no silicone |
-
no silicone |
non halogen 1) no silicone
|
non halogen 1) no silicone
|
non halogen 1) no silicone
|
Máte zájem o tento produkt? Potřebujete další informace nebo individuální ceny?
musíš být přihlášen
Air saturation with water level (humidity) depends on the temperature. In case of big temperature difference between inside and outside of the casing, the water condensation inside of the casing appears.
Example: During load change![]() |
Turn on system.
Inside temperature is usually higher then outside because of devices power losses. |
![]() |
Warm air inside the cabinet absorbs humidity, which penetrates from outside, because cabinets are not gas tight.
|
![]() |
System turned off.
Inside temperature lowers because devices are turned off. Colder air emits water, which liquefy on the inside surfaces. |
It appears especially in places, where there are big temperature jumps, in the internal installations, inside buildings.
|
![]() |
![]() In order to keep high IP level ventilation is protected by special ventilation throttles. Because of breathing membranes they provide pressure equalization. |
New ventilation gland KOMBI allows to insert cable and additionally it compensates pressure.
Kombi glands protects from accumulation of water which occur usually because of big temperature differences. ![]() |
-for inside and outside installations
|
- Material: Thermoplast
- with lightening and counter nut |
- IP: IP 66 / IP 67
- Colour: grey, RAL 7032 |
![]() |
KBM 20 |
Kombi ventilation glands
|
---|---|---|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 20 x 1,5 Tightening level: Ø 6-13 mm gland hole: Ø 20,5 mm one ventilation gland M20 must be used for 6 litres (6000 cm3) casing capacity. |
||
![]() |
KBM 25 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 25 x 1,5 Tightening level: Ø 9-17 mm gland hole: Ø 25,5 mm one ventilation gland M25 must be used for 11 litres (11000 cm3) casing capacity. |
||
![]() |
KBM 32 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 32 x 1,5 Tightening level: Ø 13-21 mm gland hole: Ø 32,5 mm one ventilation gland M32 must be used for 13 litres (13000 cm3) casing capacity. |
||
![]() |
VSB 13 |
Stopper
|
diameter: 13 mm
for ventilation glands i M20 or M25, which are not used for cable ducting Colour: Red, RAL 3000 |
||
![]() |
VSB21 |
Stopper
|
diameter: 21 mm
for ventilation glands i M25 or M32, which are not used for cable ducting Colour: Red, RAL 3000 |
-for inside and outside installations
|
- Material: Thermoplast
- with lightening and counter nut |
- IP: IP 66 / IP 67
- Colour: black, RAL 9005 |
![]() |
KBS 20 |
Kombi ventilation glands
|
---|---|---|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 20 x 1,5 Tightening level: Ø 6-13 mm gland hole: Ø 20,5 mm ventilation gland M20 must be used for 6 litres (6000 cm3) casing capacity. |
||
![]() |
KBS 25 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 25 x 1,5 Tightening level: Ø 9-17 mm gland hole: Ø 25,5 mm ventilation gland M25 must be used for 11 litres (11000 cm3) casing capacity. |
||
![]() |
KBS 32 |
Kombi ventilation glands
|
incandescent wire test IEC 60 695-2-11 960°C
Thread ISO: M 32 x 1,5 Tightening level: Ø 13-21 mm gland hole: Ø 32,5 mm ventilation gland M32 must be used for 13 litres (13000 cm3) casing capacity. |
||
![]() |
VSB 13 |
Stopper
|
diameter: 13 mm
for ventilation glands M20 or M25, which are not used for cable ducting Red, RAL 3000 |
||
![]() |
VSB21 |
Stopper
|
diameter: 21 mm
for ventilation glands i M25 or M32, which are not used for cable ducting Red, RAL 3000 |
Glands for areas endangered with explosion
|
- with load and counter nut
-material - poll amid
|
- IP IP 65
- colour: black, RAL 9005 |
![]() |
AXM20 |
Thread: M20 x 1,5
For cables: Ø 5,5 - 13 mm |
assembly hole: Ø 20,5 mm
Wall thickness: 1,5 - 2 mm |
---|---|---|---|
AXM25 |
Thread: M25 x 1,5
For cables: Ø 8 - 17 mm |
assembly hole: Ø 25,5 mm
Wall thickness: 1,5 - 2 mm |
|
AXM32 |
Thread: M32 x 1,5
For cables: Ø 12 - 21 mm |
assembly hole: Ø 32,5 mm
Wall thickness: 1,5 - 3 mm |
|
AXM40 |
Thread: M40 x 1,5
For cables: Ø 17 - 28 mm |
assembly hole: Ø 40,5 mm
Wall thickness: 1,5 - 3 mm |
-for inside and outside installations
|
- Thread ISO: M 12 - M 63
- gland hole: Ø12.5 - 63.5mm |
- material: Thermoplast
- Wall thickness: up to 3 mm |
![]() |
AKM |
Twisted gland
|
---|---|---|
IP: IP 65
Tightening level: Ø 3 mm - 48 mm Colour: grey, RAL 7035 incandescent wire test IEC 60 695-2-11 750° C |
||
![]() |
ASM |
Twisted gland
|
IP: IP 66
Tightening level: Ø 3 mm - 48 mm Colour: grey, RAL 7035 incandescent wire test IEC 60 695-2-11 960° C |
||
![]() |
ASS |
Twisted gland
|
IP: IP 66 / IP 67
Tightening level: Ø 2 mm - 48 mm Colour: black, RAL 9005 incandescent wire test IEC 60 695-2-11 960° C |
-for inside and outside installations
|
- incandescent wire test
IEC 60 695-2-11 750° C |
- for holes M 16 - M 40
- gland hole Ø 16.5 - 40.5mm |
- material: Thermoplast
- Colour: grey, RAL 7035 |
![]() |
ESM |
Push in gland
|
---|---|---|
IP: IP 55
Tightening level: Ø 4.8 mm - 30 mm Wall thickness: 1.5-3.5 mm |
||
![]() |
STM |
Multi range gland
|
IP: IP 55
Tightening level: Ø 3.5 mm - 34 mm Wall thickness: 1.5-4 mm |
||
![]() |
EDK |
Push in gland
|
IP: IP 65
Tightening level: Ø 5 mm - 30 mm Wall thickness: 1.5-3.5 mm |
||
![]() |
EDR |
Push in gland for installations pipes
|
IP: IP 65
For pipes: M 16 - M 40 Wall thickness: 1.5-3.2 mm |
Operation condition
/material property |
ESM...
STM... EDK... EDR... KST... MV FP 66 |
Ste...
|
ASM... AKS...
|
ASS...
|
AKM...
|
---|---|---|---|---|---|
Ambient temperature - mean value 24h |
+35°C | +35°C | +55°C | +55°C | +55°C |
- max value | +40°C | +40°C | +70°C | +70°C | +70°C |
- min value | -25°C | -25°C | -25°C | -25°C | -25°C |
Flammability -incandescent wire test | 750°C | 650°C | 960°C | 960°C | 750°C |
IEC60595-2-1 | - | - | V-0 | V-2 | V-2 |
-UL Subject 94 | Flame resistant, self extinguishing | Flame resistant, self extinguishing | Flame resistant, self extinguishing | Flame resistant, self extinguishing | |
Toxins emission |
non halogen 1)
no silicone |
-
no silicone |
non halogen 1) no silicone
|
non halogen 1) no silicone
|
non halogen 1) no silicone
|
Vaše hodnocení nelze odeslat
Nahlásit komentář
Zpráva odeslána
Váš podnět nelze odeslat
Napište svůj názor
Zkontrolovat před odesláním
Vaši recenzi nelze odeslat