Vamzdžių suvirinimo siūlių šildymas

Tube and Pipe Coating Curing

Ambrell induction heating solutions are fast, efficient choices for all stages of the curing operation.

In preparation for coating, induction heating is used to remove surface moisture from pipes, preheating the pipe to the correct temperature for coating. Then – depending on the type of polymeric coating applied – the tube or pipe is heated to 150-300 °C (302-572°F) for curing the coating.

In addition to requiring less floor space than traditional furnaces and ovens, induction systems offer ergonomic benefits, are environmentally friendly, and have the unique capacity to selectively heat only portions of a tubular product.

Beyond these operational benefits, induction heating also delivers a higher quality coating solution. Unlike furnaces that rely on heating the coating first, induction heats the metal substrate beneath the coating – curing the coating from the inside out – leaving the surface soft and allowing solvents to evaporate and any outgassing to occur. Removing coatings to recover tubes and pipes for re-coating is another common use for induction heating. Typically, the pipe is heated to about 200 °C (392 °F), which breaks the bond between the surface and coating, allowing the coating to be peeled off. Using this method is more environmentally friendly than alternative methods of burning off or grinding off the coating.

Pre- and Post-Weld Heating

With the use of more thin-wall steel alloy pipes in today’s oil and gas pipelines, manufacturers and installers are turning to the fast, accurate and uniform heating of Ambrell induction heating systems. During the process of butt welding, induction heating is commonly used to preheat the joint area to 150-200 °C (302-392 °F) to prepare the area for a consistent quality weld. After welding, the joint area is heated to 600-650 °C (1112-1202 °F) for thermal stress relief of the weld area. Traditional gas flame and resistance heating systems are often impractical when these higher temperatures are required. Not only are they too slow to meet the cycle times demanded by the industry, but also the heating can be inaccurate and can lack uniformity around the full circumference and bandwidth of the weld joints.

Other benefits of induction heating include:

• Variable control over temperature/time parameters
• Minimal damage to factory coating, and no deleterious surface residues
• No open flames or exposed heating elements
• Reduces energy costs, and eliminates the need for large gas storage area

Induction heating is the preferred heating method for bending of larger thicker walled pipes. This is due to the focused narrow band heating offered by the induction process with the resulting higher quality bends with lower quality and wall thinning than other bending methods. Because of this quality and accuracy, induction hot pipe bending is the preferred alternative to traditional fit-and-weld procedures, and can help companies meet the rigorous safety demands of the chemical and energy industries. Ambrell induction heating systems are available in the frequency and power levels to optimally heat any pipe for hot bending. Typically, induction hot bending is used on pipes with diameters from 2” (50mm) to 36” (915 mm), with wall thicknesses from Schedule 5 up to 2.5” (64mm).

Hot pipe bending with induction involves placing an induction heating coil around the pipe at the bend point, and heating a 1” (25mm) section of the pipe to 1000 °C (1832 ^°F). With the pipe at temperature, pressure is applied by a bending arm to bend it into the desired shape. Air and water quenches are used before and after the heat zone to promote bending solely at the hot zone.

Induction heating is the preferred heating method for bending larger thick-walled pipes used in the chemical and power generating industries.

Drill Pipe Manufacturing

Ambrell supplies induction heating systems to companies that manufacture oil and mineral drill pipe to meet the requirements of API 5DP and GOST R 50278. Induction heating offers many benefits over flame or resistance heating during the manufacturing processes in drill pipe heat treating and welding of the tool posts onto the pipe ends, including:

• Consistency: Heat is generated within the part for precise, rapid, even heating
• Quality: Temperature variations that are seen in flame heating are eliminated
• Productivity: Faster heating enables single-part processing
• Safe: No exposed flame for a safer working environment
• Economical: Heat is applied only where it is needed

Ambrell induction heating systems allow the depth and rate of the heating to be precisely controlled, delivering the ideal temperature and timing for each step in the process, while meeting the 180 seconds floor to floor time cycle.

Brazing Diamond or Carbide Inserts onto Oil and Gas Well Drill Bits

Oil and Gas Well Drill Bits

Ambrell offers a wide power and frequency range with its EASYHEAT and EKOHEAT systems. So, whether your tube or pipe application is large or small, Ambrell can help you maximize cost efficiencies and productivity.

Ambrell’s systems are versatile with multiple capacitor and tap transformer configurations. They offer efficient power conversion, which minimizes energy expenses. They are also user-friendly, offer agile frequency tuning for repeatable heating, and can be easily integrated into your process thanks to their small footprint.

Systems include:

• Ease of integration into production processes with a portable workhead – up to 30m in some systems
• Wider frequency ranges allow more tubes and pipes of varying specifications to be heated with the same power supply
• Multiple capacitor and tap transformer configurations for a more versatile system than the competi-tion
• Agile frequency tuning for accurate, repeatable heating
• Efficient power conversion minimizes energy expenses
• Expert coil designs that maximize power delivery and save production time
• User-friendly operator interface in five languages (EN, ES, FR, DE, IT)